Here is the small report how we have made this cutting board.
This time the cutting board stays Kentucky.
The Pole Vault cutting board was made for the custom order as a gift for the pole vaulting trainer who had been participating in Olympics games in 2012 in London.
The board size is 18,5*12,5*2″
Types of wood: maple, walnut, ash, light cherry, dark cherry, red oak
How to find inlay parameters.
How to find inlay parameters.
Feed rate v bit 30ipm https://amzn.to/3wf9Txg ???
Feed rate flat nose 1/8 40ipm https://amzn.to/3izKXcF ???
For orders go to https://broinwood.com/pages/custom
Check out our Instagram page https://www.instagram.com/broinwood/
https://broinwood.com/
???Here some stuff which I use in my workshop and really love it.
Maybe it will be useful for you.???
Definitely recommend this Oil and Wax for cutting board:
https://amzn.to/36ytyi1
https://amzn.to/3nrAPGL
My glue:
https://amzn.to/3jyVMNu (really love it)
Double-Sided Duct Tape:???
https://amzn.to/33ANxen (It holds blank well, but anyway, I also use screws.)
My Random Orbit Sanders I love how they work but they get a little dusty:
https://amzn.to/36u5mxs
https://amzn.to/3d1oNiv
Makita 3/4-Inch ID/1-OD diameter by 10-Foot Hose
https://amzn.to/33uGmnS
My Sanding Disc (for me they are the best!!!):
3M Cubitron II
https://amzn.to/2SrnAHs (80 and 120 grit)
https://amzn.to/2SqlvvH (150 grit)
https://amzn.to/3nksyUQ (220 grit)
https://amzn.to/2GriKaZ (320 grit)
My router bits which I use a lot:
My favorite router bit!!!:
Metric CNC 2D and 3D Carving 6.2 Deg Tapered Angle Ball Nose (clean cut, long life, definitely recommend) ???
https://amzn.to/3wf9Txg
2D & 3D Carving 12.4 Deg Tapered Angle Ball Tip x 1/32 Dia x 1/64
https://amzn.to/3sviUAl (clean cut, long life, definitely recommend)
Standard Spiral Bit with Down Cut 1/8-Inch Cutting Diameter
https://amzn.to/3izKXcF
15 Degree v bit (be careful easy to break down)
https://amzn.to/3izLyLr
Round Nose Bit with 3/8-Inch Radius, 3/4-Inch Cutting Diameter and 1-1/4-Inch Cutting Length
https://amzn.to/2SsZYlV (I use it for juice groove)
1/2-Inch Dia. 2 Flute Ball Nose Spiral End Mill Router Bit
https://amzn.to/33v99Zm (I use it for juice groove)
Spiral Flush Trim Bit with Down Cut and 1/2-Inch Cutting Diameter
https://amzn.to/2SsB8m7
Three Flute with Spiral Bit 1/2-Inch Cutting Diameter and 2-Inch Cutting Length
https://amzn.to/2HTgwkV (I use it for flatining surface and makining cutting board shape)
Spiral Bit with Up Cut 1/4-Inch Cutting Diameter and 1-Inch Cutting Length
https://amzn.to/36u2Hns (I use it for cut off inlays. it doesn’t make chips.)
My Collet Set:
https://amzn.to/33xbO4X
My DEWALT Plate Joiner:
https://amzn.to/33xtkWQ (it is not bad and not good it is ok)
My Bandsaw Blade it is inexpensive and cut well:
https://amzn.to/34uKNy8
Hi,
My name is Nik. Welcome to my channel!
I appreciate your likes and subscriptions!
Sincerely,
Nik.
source
Comments are closed.